Import Guides

Pre-shipment inspection for tiles: shade, caliber, warpage, packing and AQL

Pre-shipment inspection for tiles: shade, caliber, warpage, packing and AQL

Once a container is sealed at Mundra, every problem inside it becomes expensive: a shade mix discovered on site, boxes of the wrong caliber, warped slabs, crushed pallets. A pre-shipment inspection (PSI) is the last moment when those problems can be fixed at the factory’s cost rather than yours. This guide explains what a good tile inspection checks, how AQL sampling works for a typical 20ft load, and how to build inspection into your order.

Key takeaways

  • Inspect when 80–100% of the order is packed, against a signed golden sample and a written specification.
  • The four things that cause most tile disputes are shade, caliber, warpage and packing.
  • AQL sampling (ISO 2859-1, general level II) tells the inspector how many boxes to open and how many defects are acceptable.
  • Supervise loading and keep photos and video of every pallet, the seal and the container number.
  • Write the inspection, the tolerances and the claims procedure into the proforma — and, if you pay by LC, into the documents.

Before the inspection: the reference

An inspector can only check against something. Before production starts, agree three things in writing:

  • A golden sample for each design, signed by both sides, with one copy at the factory and one with you. For designs with strong variation, keep a small shade bank showing the acceptable range.
  • A specification sheet in the purchase order: grade, size and thickness, rectified or not, finish, water absorption (≤0.5% for porcelain), breaking strength, slip rating where relevant, and the packing specification.
  • Shade and caliber rules: one shade per lot per design, and shade and caliber codes printed on every carton.

What to check

1. Shade

Tiles from different firings can differ slightly in colour. The inspector lays out tiles from several boxes of the same design side by side under good light, compares them with the golden sample and checks that every carton of a lot carries the same shade code. A mixed shade within one lot is a major defect, because it shows on the floor and cannot be fixed after installation. Colour difference can also be measured instrumentally under ISO 10545-16 if your specification calls for it.

2. Caliber

Caliber is the actual work size of a batch. Tiles of different calibers in one area give uneven joints, especially with narrow grout lines on rectified tiles. The inspector measures length, width and diagonals on sampled tiles and checks them against the caliber code on the box and the tolerance for the product class.

3. Warpage and flatness

Warpage — edge curvature and centre bow — is measured under ISO 10545-2 and compared with the tolerances in ISO 13006 / EN 14411 for the product type. It matters most on large formats such as 600×1200, 800×1600 and slabs, where small deviations cause lippage. The inspector also checks edge straightness and rectangularity, and thickness.

4. Surface and visual defects

From a standing distance, then close up: chips, pinholes, glaze faults, print defects, scratches on polished surfaces, and breakage inside cartons. For polished tiles, check that a protective film or interleaf has been applied where specified.

5. Packing and marking

  • Cartons: correct design name, size, grade, shade, caliber, quantity and country of origin; strength and dryness.
  • Pallets: ISPM-15 stamped or plastic, corner boards, top caps, two to three rounds of strapping, stretch wrap, polythene or foam between polished faces.
  • Slabs: A-frames or crates, with separators between faces.
  • Pallet labels that match the packing list.

6. Loading

Ask for loading supervision, or at least a full photo and video record: empty container condition, each pallet as it goes in, airbags or dunnage in voids, bracing at the doors, the seal number and the container number. Good packing and loading keep in-transit breakage below about 1%; the industry commonly accepts a 1–2% allowance. Poor palletising can push breakage to 4–10%, and the loading record is what decides a claim.

How AQL sampling works

An inspector does not open every box. AQL — acceptance quality limit — sampling uses the tables in ISO 2859-1 to set how many units to examine and how many defects are acceptable before the lot fails. For general inspection, level II is the usual choice.

A worked example: a 20ft container of 600×1200 GVT holds roughly 760–900 boxes. For a lot of 501–1,200 units, ISO 2859-1 at general level II gives code letter J, which means a sample of 80 boxes. A common setting is zero tolerance for critical defects, AQL 2.5 for major defects and AQL 4.0 for minor ones. At AQL 2.5 with a sample of 80, the lot is accepted with up to 5 major defects and rejected at 6. Check the current table with your inspection agency; the principle is what matters.

Two practical points. First, define what counts as critical, major and minor for tiles before inspection — for example, shade mix within a lot as major, a single chipped corner as minor. Second, AQL samples boxes, but some checks, such as shade comparison across boxes and slab surfaces, deserve a wider look. For large slabs, a 100% surface check is reasonable.

Who inspects, and at what cost

Options range from the factory’s own quality team (with photos and video) to an independent agency such as SGS, Bureau Veritas, Intertek, TÜV, QIMA or V-Trust. In India, a third-party container visit has been costing roughly ₹8,000–20,000. In China, inspection is often priced per man-day, from about USD 300; budget around USD 300–450 per container.

Some markets require a conformity inspection anyway. Kenya’s KEBS PVoC, Tanzania’s TBS PVoC, Nigeria’s SONCAP and Iraq’s COSQC certificate of conformity all involve an appointed agency before shipment. These are regulatory checks, not a substitute for a quality inspection against your golden sample, but the two can often be scheduled on the same visit. See the market pages for Kenya, Tanzania, Nigeria, Iraq and Ghana.

Writing inspection into the order

  1. Name the inspection type (PSI at 80–100% packed, plus loading supervision if wanted) and who pays.
  2. Attach the specification and refer to the golden sample.
  3. State the AQL levels and defect classification.
  4. State what happens if the lot fails: re-sorting or replacement at the factory, and re-inspection at the factory’s cost.
  5. State the claims procedure after arrival: photos of the intact seal and damaged pallets within a few days of devanning, and quality claims only before installation.
  6. If you pay by letter of credit, add the inspection certificate to the documents. Our LC checklist explains how.

The short version

Agree the reference before production, inspect the four things that cause most disputes — shade, caliber, warpage and packing — sample by AQL, and keep a loading record. It costs a fraction of one pallet and protects the whole container. Our container loading guide covers how many boxes and pallets to expect in a 20ft.